What is a crankshaft position sensor?The crankshaft position sensor is located near the engine's crankshaft, and relays information about the crankshaft’s position as it rotates. Show
 How does the crankshaft position sensor work?As the crankshaft spins, the position sensor magnetically reads its position. This information is constantly sent to the engine's computer for comparison with data from the camshaft position sensor. When the two signals reach the computer, they must match; otherwise, the computer will think there is a mechanical error in the engine and will adjust some settings in response. What are the symptoms related to a bad crankshaft position sensor?When the computer senses the engine is out of time, it will turn on the check engine light, and the engine may start and stall, or fail to start at all. If the engine runs, it will run poorly, and get bad fuel mileage. » LEARN MORE: Symptoms of a bad crankshaft position sensor Can I drive with a crankshaft position sensor problem?Driving a vehicle with a failed camshaft or crankshaft position sensor is usually impossible. If driving is possible, it is not recommended. If the sensor is functioning normally and reporting an error, the engine may be out of time or may have suffered a mechanical failure. How often do crankshaft position sensors need to be replaced?There's no set replacement interval for the crankshaft position sensor, and on many cars, the part will last the lifetime of the vehicle. It's not uncommon for it to fail, however, and the likelihood increases once you pass 100,000 miles.
Need help locating the crankshaft position sensor on a 2011 Dodge Avenger 2.4 litre Recommended Services
Hi there. The crankshaft position sensor is located at the rear of the engine block near the transmission. Unfortunately I cannot send over any pictures. If you need to have your crank sensor replaced, consider YourMechanic, as a certified mechanic can come to your home or office to replace the crankshaft position sensor. The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details Get an instant quote for your carOur certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing Experienced Mechanic?Earn up to $70/hrWhat others are askingWarning lights and PO344 Camshaft Position Sensor This vehicle came with three different engines and they all have different directions to replace the sensors. The sensors also may have specialized removal and installation procedures that require special tools for the seals and sensors. The code P0344 is... wheel alignment Hello, thanks for writing in. I will be happy to assist you with your concern about whether a wheel alignment must be performed after the installation of sway bar links in the front and shock absorbers in the rear of... My fog lights aren't working. The fog lights are controlled through the smart junction box in the right kick panel. The switch signals the box to ground the fog light relay in the engine compartment fuse relay box. The number 58 fuse powers the relay... Loud sound on car when it start It is possibly a starter motor, drive belt, engine, or exhaust system noise. There are other possibilities, too, but If you request an engine noise diagnostic (https://www.yourmechanic.com/services/car-is-making-a-noise-inspection), the responding certified mechanic will get this resolved for you. If you have... Related articlesHow Long Does a Cylinder Head Temperature Sensor Last? The The engine’s performance is largely based on temperature measurements performed by the engine control module (ECM), also known as the vehicle’s computer. As the temperature of the engine increases, the resistance decreases which means the voltage drops. The computer... How to Replace an EVP Position Sensor The EGR valve is monitored by a valve position sensor. This sensor helps your car's EGR system to run more efficiently and better control emissions. Where is the crank crankshaft position sensor located?The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block. Will a malfunctioning Cam or Crank Sensor illuminate the check engine light or affect vehicle operation?
|
2011 dodge avenger crankshaft position sensor location
Related Posts
Copyright © 2024 en.idkuu.com Inc.
