Document Show Schlage Encode Smart DeadboltSchlage Encode Smart Deadbolt Quick Start GuideStart here!schlage.com/encode-workswith Visit schlage.com/encode-workswith to setup and control your with your smartphone.TouchscreenCommunication Icon
Low Battery Icon
Programming and Input LED
Home Button and Checkmark Icon
Lock Button and “X” Icon
ToolsPhillips screwdriver Don’t use a power drill! Step 1Remove existing lock.Remove the entire deadbolt, including the bolt. You may also want to remove the strike. A standard Schlage deadbolt is shown. Check with your specific deadbolt manufacturer if you need help. Step 2Need Help?Visit schlage.com/faqs-encode Install the bolt.You may have to adjust your bolt length. Make sure the slot in the bolt is centered in the hole. Step 3Need Help?Trouble installing the strike reinforcer? Install the strike into the door frame.If you have a window next to your door, you may not be able to use the longer wood screws to install the reinforcer. Step 4Is it hard to install
the touchscreen? Install the touchscreen.Route the cable through the door BELOW the bolt. Align the tailpiece as shown and push the touchscreen onto the door. Step 5Phillips screwdriver Don’t use a power drill! You may damage your lock! Install the backplate.Route the cable under the bolt and through the hole on the bottom of the backplate. Secure the backplate with screws. Make sure the outside touchscreen is straight before tightening screws all the way. Step 6Connect the cable.Tuck the cable and connector in the space above the spindle. Step 7Phillips screwdriver Don’t use a power drill! You may damage your lock! Secure the lock to the door.If the bump on the tailpiece doesn’t align with the slot in the back of the inside assembly, make sure your thumbturn is vertical (up and down). Step 8Install batteries and slide the cover on.That wasn’t so bad, was it?Your lock is now installed! Remember, you still have to set up your lock to use it. Step 9Set up your lock.1. Open your door! Final test!1. Close your door. Need Help? Now that your lock is installedyou can use a smart home system to lock and unlock your door from anywhere and add user codes for guests and household members. schlage.com/encode-workswith Visit schlage.com/encode-workswith for a list of compatible smart home apps that allow you to control your with your smartphone.Lock and unlockTo lock your door just tap the lock icon.You can also lock your door from inside by turning the thumb turn toward the door edge. To unlock your door enter a user code.You can also unlock your door from inside by turning the thumb turn away from the door edge. Questions about your
new Please don’t return it to the store!Let us help you first! www.schlage.com/faqs-encode © Allegion 2018 DOWNLOAD RESOURCES
FAQ’SHow do you change the code on a Schlage encode deadbolt? Code press the outside Schlage button enter the current programming. Code. Then press three enter. The new six digit programming. Code. Enter it again to confirm. How do I program Schlage Encode smart WIFi deadbolt? After the deadbolt is installed insert the battery pack and observe the power up confirm that the deadbolt beeps. And that the keypad lights. Up. If the lock does not beep or the keypad lights do not How long do Schlage encode batteries last? It provides room for four AA batteries, which Schlage says can last up to six months when the lock is used on Wi-Fi or up to a year if you use it with Thread. Can Schlage Encode be hacked? Our Schlage Encode Smart WiFi Deadbolt, Schlage Sense™ Smart Deadbolt, Schlage Connect™ Smart Deadbolt with Alarm, and Schlage Touch™ Keyless Touchscreen Deadbolt and Lever have all received a grade A in security, the best possible grade to keep your home, and everything inside it, safe. Does Schlage Encode come with a key? Schlage provides the first set of four AA batteries needed to operate the lock, and it comes with one (and just one) mechanical key should the batteries die. As with most smart locks, the Encode has a too-short electrical cable that connects the lock’s circuit board to its power supply. What if I lost my Schlage programming code? The default programming code is printed on a label on the programming guide that came with your lock. If you do not have access to the guide, remove the lock from the door and look on the back of the lock for a label containing the default code. How do you open a Schlage lock with a dead battery and no key? Touch a new high-quality alkaline 9-volt battery to the contacts below the bolt throw. Do Schlage locks have a lifetime warranty? Schlage stands behind its products and will continue to do so with a limited lifetime mechanical and finish warranty, a three-year limited electronics warranty and dedicated resources, customer support and innovation. Do Schlage locks have cameras? The lock’s integration with Key enables users to operate their deadbolt in concert with Ring video doorbells and cameras, streamlining control of their home’s security. Ring customers will now be able to lock and unlock their door directly from the Live View of their camera in the Ring app. Does Schlage Encode have backlight? The Schlage Encode comes with a backlit keypad and a traditional keyway. The lock is powered by four AA batteries, set in the back of the lock. Why is my Schlage lock blinking red? The Schlage button flashes red continuously. It”s mean… The battery is dead. You will need to replace the battery immediately. How do you change the 4 digit code on a Schlage encode lock?To change the default 4-digit code on a Schlage lock, follow these steps.. Step 1: Find your programming code. ... . Step 2: Enter your programming code. ... . Step 3: Press the Schlage and number 1 button simultaneously. ... . Step 4: Enter your new entry code. ... . Step 5: Enter your 4-digit code again to confirm.. |