Show $500.00 Dana 60 Front Axle $500 It belong to a 1987 Ford F250 . You will have to pull i
$950.00 1991 Dodge matching set Dana 60 and Dana 70 Complete axles 3.54 gears Both are
$6,000.00 Custom width will fit under any Jeep, custom high steer tie rod and high pinion
$3,200.00 Dana 60 with Eaton electric locker 5:38 gears I also have a set of 4:88 if you w
$1,450.00 GM 14 bolt has a truss welded on to it and I believe it has a Limited slip and 4
$1,300.00 1977 Chevy, what's left of my parts truck. The truck does have a dana 60 front a
$1,300.00 1977 Chevy, what's left of my parts truck. The truck does have a dana 60 front a
$400.00 Missing axle shafts and wheel bearings but it’s still a good axle I just sold
$500.00 I have an un-assembled brand new Axle Truss and Hydraulic Cylinder mount for a
$500.00 have an un-assembled brand new Axle Truss and Hydraulic Cylinder mount for a Ch
$800.00 Dana 60 rear and Dana 44 front from 1969 Ford F-250. Axles are in good shape, bu
$150.00 Dana 60, rear open diff C-clip semi-float and 3.73 gear, and front 3.73 gear (no
$50.00 Gears out of my truck did cummins swap had to regear my axles just have one set
$50.00 Came off 03 ford f350. Drivers side axle shaft for Dana 60. I bought it for mine
$500.00 Dodge axles. Have both 3.54 ratio and 4.10 ratio for sale. Call or text with que
$300.00 Was going to use it for a rock crawler build , but went a different way.
$1,000.00 I have Dana 60 front and Dana 70 rear axle for sale from a dodge. I got them for
$1,500.00 2006 Ford Super Duty Axles high pinion Dana 60 front and Sterling 10.5 rear. 3.7
$1,200.00 I am selling a 1985 thru 1991 ford F350 dana 60 kingpin axle with 4.10 gear rati
$1,000.00 1966 Dana 60 rear axle was most recently in a 1971 highboy. Working factory limi
$300.00 Chevy Dana 60, 30 spline axles. 300.00. Please contact Tommy @801-979-5859
$100.00 I bought this thinking it would work for my application. Turns out I need a diff
$50.00 Spicer Dana 60 open carrier, side and spider gears in great shape. 4.10 and dow
Is a Ford Dana 60 the same as a Chevy Dana 60?If there are 7 bolts, then you have a GMC/Chevy or Jeep Dana 60 axle. These axles are all exactly the same. If there are 4 bolts, then you have either a Dodge or Ford Dana 60 axle. These two axles are not identical.
Are Dodge and Chevy Dana 60 the same?Absolutely! The GM Dana 60 parts you have and the Dodge Dana 60 parts you have are interchangeable. Since you are sticking with 4.10:1 ratio gears, there isn't even a carrier split to worry about. The 3.55:1 ratio gears and 4.10:1 ratio gears ride on the same carrier.
Where can I find a Dana 60?Many Dana axles have the model ID cast into the fins or centersection. Look for a "44" or "60" cast into the reinforcement ribs. The number can usually be found on the lower right side rib below the differential cover, but it may also be found on other ribs or on top of the main cast structure.
How much HP can a Dana 60 take?Additionally, the Dana 60 (S60) from Strange comes equipped with their beefy 35-spline alloy axles and carrier that can handle over 1,000 horsepower. A vintage Dana 60 like ours with its stock 23-spline axles and clutch-type Sure-Grip is limited to roughly 700 horsepower of sticky tire, strip action.
|