Garage-Pro is the most affordable brand for your old, worn-out, or damaged factory part! This premium quality replacement part is made to give your car, truck, and SUV that original factory look and performance. Available for different applications, our Garage-Pro part will surely fit right to your vehicle. Comes with 1-year unlimited mileage warranty! Anyone just can't fail by using Garage-Pro! Garage-Pro definitely will indulge you as well as your vehicle starting with your very first purchase! Kia Sorento Tail Light Bulbs Replacement Guide
Owners of other Kia and Hyundai vehicles such as the Optima, Forte, Cadenza, K900, Rio, Sportage, Sedona, Soul, Elantra, Veloster, Sonata, Azera, Tucson, Santa Fe, Genesis and Equus may also find these DIY instructions to be helpful. Replacement bulbs with their part numbers are as follows: Brake # 2357, Rear Turn Signal # 1156A(or 1156NA), Side Marker # 168, Parking Light # 2357and Reverse Light # 921. The tools needed to replace the bulbs include a Phillips head screwdriver and a flathead screwdriver.  Remove Lower Phillips Screw Two Phillips Screws Removed Pull Off Tail Light Assembly The first two steps are to open the tailgate door and then move to the side of the vehicle with the burnt out tail light bulb. Remove the two screws along the inner edge of the tail light housing by turning them counterclockwise with the Phillips head screwdriver. Set the two screws aside in a safe place. Pull the tail light housing straight off the rear of the vehicle. The assembly is still held in place by two metal pegs on the back side near the outer edge that act as friction fasteners. If you have trouble removing the tail light housing, try gently wiggling it back and forth while pulling it straight off. Turn Over Tail Light Housing 1/4 Turn Counterclockwise Remove Brake Light Bulb Socket Turn over the tail light housing to access the brake, rear turn signal and side marker bulb sockets. Rotate the large grey brake light bulb socket 1/4 turn counterclockwise and pull it straight out of the housing. Push Down & 1/4 Turn CC 1/4 Turn Clockwise - Lock 1/4 Turn Counterclockwise Push the old brake light bulb down in to the socket and rotate it 1/4 turn counterclockwise before pulling it straight out. Push a new # 2357bulb down in to the socket and rotate it 1/4 turn clockwise to lock it in place. Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place. To replace the turn signal bulb, rotate the orange socket 1/4 turn counterclockwise before pulling it straight out of the housing. Remove Turn Signal Bulb Rear Side Marker Socket Replace # 168 Bulb Push the old turn signal bulb down in to the socket and rotate it 1/4 turn counterclockwise before pulling it straight out. Push a new amber colored # 1156Abulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place. Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to lock it in place. To replace the rear side marker bulb, rotate the small grey plastic socket 1/4 turn counterclockwise and remove it from the housing. Pull the old side marker bulb straight out of the socket and push in a new # 168bulb. If necessary, you may also be able to use any other miniature wedge base bulbs such as the # 158, 194, W5W, 2825 or a compatible LED unit. Re-insert the side marker bulb socket in to the housing and rotate it 1/4 turn clockwise to secure it in place. Line Up Metal Pegs & Grommets Replace Phillips Screws Tighten Screws Clockwise To re-install the tail light housing, line up the two metal pegs or "spikes" on the back side with their corresponding plastic grommets. Push the tail light assembly back in to place on the rear corner of the vehicle. Replace the two screws on the inner edge of the housing and tighten them in the clockwise direction with the Phillips head screwdriver. Try to avoid over tightening the two screws to prevent from cracking the plastic tail light housing. Tailgate Light Housing Open Tailgate - Access Cover Screwdriver In Notch The parking light and reverse light bulbs are located in a separate housing on the tailgate door. To access the bulbs, open the tailgate door and locate the rectangular access panel. Pry open the access cover by inserting a flathead screwdriver in to the notch on the top edge. Access Panel Removed Parking & Reverse Bulb Sockets Push Down & 1/4 Turn CC Set the access cover aside in a safe place. Rotate the large orange parking light bulb socket 1/4 turn counterclockwise and pull it straight out of the housing. Push the old bulb down in to the socket and rotate it 1/4 turn counterclockwise before pulling it straight out. Push a new # 2357bulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place. Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to lock it in place. Reverse Bulb Socket Pull Out Old # 921 Bulb Line Up Access Cover To replace the reverse bulb, rotate the small grey socket 1/4 turn counterclockwise before pulling it straight out of the housing. Pull the old reverse bulb straight out of the socket and push in a new # 921bulb. Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place. Line up the access panel and gently pop it back in to place. Push In Access Panel Test Turn Signal & Reverse Testing Brake Light Bulb To test the new tail light bulbs, have someone step on the brake pedal, activate the hazard signals and place the transmission in reverse. For more, check out my other Kia Sorento DIY Repair & Maintenance Guides. What kind of brake light bulb does a 2014 Kia Sorento take?Sylvania LED Mini Bulb 2357RSYLLED.
How much is a brake light for a Kia?Our Brake, Stop, and Tail Lights OEM and aftermarket parts range from $1.79 to $159.99 for the Kia Forte. If you're interested in a specific brand of Kia Forte Brake, Stop, and Tail Lights products, we carry popular brands like Sylvania.
|
2014 kia sorento brake light bulb replacement
Related Posts
Copyright © 2024 en.idkuu.com Inc.
